special designed 10A ESC(programmable) and 120 motor combine as a special value combo.
ATTENTION: 10A ESC SALE PROMOTION FOR WHOLESALE CUSTOMERS, PLEASE SEND US EMAIL FOR MORE INFORMAITON!!!!! |
|
|
|
| Specifications︰ | 120 series motor( any KV motor)+ 10A ESC, special value combo.
User Manual:
FG-10A User manual ( V2.1)
ONE: Functional Introduction
1.FG-10A have very good protection functions, include;
a.start protection（when connect ESC power, throttle must be in lowest position. In case the controller not power on or throttle not at lowest position, motor won’t start），
b.Lost control protection（when no good receiver signal or no ESC signal，BL motor will stop and 2 seconds after signal recover with throttle at lowest position. The operation will back to normal）
2.Maximum input voltage 15V（3cell lipo/12cell ni-mh ni-cd）;
Maximum continuous current
FG-10A: 10A (surge current 13A) with 5V/1.5A BEC（ESC, receiver and motor share this source）
3.Programmable LVCO (6.0V for 7-10cell ni-mh ni-cd 2cell lipo / 9.0V for 9-12cell ni-mh ni-cd 3cell lipo/ 70% of input voltage ). When reach LVCO, motor will shake (soft cutoff) and remind customer to land the plane and replace new battery.
4.Programmable for braking function.(ON/OFF)。
5.Programmable timing（2-7°Inrunner BL motor / 12-17°Outrunner BL motor）。
6.Programmable throttle range（1.1-1.9mS/1.2-1.8mS）for various brand controller。
TWO: Programmable setting
1.Connect ESC, motor and receiver as drawing，make sure that ESC not connect the battery.(FG-10A dont have switch)
2.Push the throttle to the highest position. (top)
3.Connect power to ESC
4.After connect battery, motor will report LVCO status by different voice（6.0V Beep---Beep-Beep / 9.0V Beep---Beep-Beep-Beep / 70% of input , you’ll hear 7 Beep sound）,After 5 seconds you’ll listen 6 fast Beep sound to remind customer enter Program mode: customer can setup LVCO, brake ON/OFF, Timing and Throttle range:
a. Put the throttle to middle position, you’ll hear one ‘Beep-’ sound, now you can setup LVCO. * pull throttle to lowest position（LVCO 6.0V）or highest position（LVCO 9.0V），you’ll hear one ‘Beep-’ sound; if you keep highest position for 7 seconds, you’ll hear 7 ‘Beep-’ sounds（LVCO is 70% of input voltage），remind customer LVCO setup finish. Now put throttle to middle position. Then you’ll hear 2 ‘Beep-’ sounds to next setup.
b. now you enter throttle setup,
* put throttle to lowest position(brake ON) or highest position（brake OFF），you’ll hear one ‘Beep-’ sound to remind user brake setup finish. Now put throttle to middle position. Then you’ll hear 3 ‘Beep-’ sounds to next setup.
c. Now you enter timing setup,
* put throttle to lowest position（2-7°inrunner BL motor）or highest position（12-17°outrunner BL motor），you’ll hear one ‘Beep-’ sound to remind user timing setup finish. Now put throttle to middle position. Then you’ll hear 3 ‘Beep-’ sounds to next setup.
d. Now you enter throttle range setup,
* put throttle to lowest position（1.2—1.8mS）or highest position（1.1—1.9mS），you’ll hear one ‘Beep-’ sound to remind user timing setup finish. Now put the throttle to the lowest position.
After about 5 seconds, you’ll hear 3 quick Beep (BeepBeepBeep) sound and this is confirm your setup finish. Now you can start the motor.
Remark:
1. If you’d like to directly to other setup menu. Just after you enter the setup program and put the throttle to middle position, wait for the sound to relative menu （a: Beep-; b: Beep-Beep; c: Beep-Beep-Beep; d: Beep-Beep-Beep-Beep）, then after different sound you can enter related menu.
2. After you finish setup, just put the throttle to the lowest position. After about 5 seconds, you’ll hear 3 quick Beep sound (BeepBeepBeep) and this is confirm that you finish setup and exit the setup menu. Now you can start the motor.
Specification:
FG-10A
Weight: 11g with wires
Size: 22mmx18mmx4mm
Continuous current: 10A
Maximum Surge current: 13A(for 10 seconds)
|
|
|
|
